Pengaruh Putaran Spindel dan Cairan Pendingin terhadap Kekasaran Permukaan Baja AISI 4140 pada Proses Pembubutan

DOI: https://doi.org/10.21070/r.e.m.v4i1.2629

Author (s)


(1)  Angga Hari Setyawan   (Teknik Mesin Universitas Muhammadiyah Sidoarjo)  
        Indonesia
(2) * Iswanto Iswanto   (Teknik Mesin Universitas Muhammadiyah Sidoarjo)  
        Indonesia
(*) Corresponding Author

Abstract


The purpose of this paper discusses how the effect of different spindle spin speeds on surface roughness, how the effect of different coolant fluid on surface roughness and is there an interaction between rotation speed of spindle and coolant to surface roughness in conventional lathe process. In this study the variable varied is the spin speed of the spindle that is is 630 rpm, 920 rpm, and 1250 rpm and the variation of coolant used is coolant, used cooking oil, and used SAE 40 oil. Then the surface roughness test was done. From the results of surface roughness test previously done the lathe process with variations of rotation speed of spindle and coolant, it can be concluded that: the highest surface roughness value was obtained during the turning process using used cooking oil coolant and spindle rotation used at 920 rpm. While the lowest value of surface roughness of the workpiece is obtained when using used SAE 40 oil coolant using a spindle rotation of 1250 rpm.



Keywords

Surface roughness; Spindle Spin Speed; Coolant Liquid



Full Text: PDF



References


[1] T. Rochim, “Teori dan Teknologi Proses Pemesinan dan Spesifikasi, Metrologi dan Kualitas Kontrol,” and others, Ed. Institut Teknologi Bandung, 2007.

[2] P. P. Yunus, “Pengaruh Jenis Pahat, Sudut Pahat dan Kedalaman Pemakanan Terhadap Tingkat Kekasaran dan Kekerasan pada Proses Bubut Rata Baja ST 42,” Jurnal Teknik Mesin, vol. 1, no. 3, 2013.

[3] W. Sumbodo, “Teknik Produksi Mesin Industry,” and others, Ed. Departemen Pendidikan Nasional, 2008.

[4] I. Lesmono, “Pengaruh Jenis Pahat, Kecepatan Spindel, Dan Kedalaman Pemakanan Terhadap Tingkat Kekasaran Dan Kekerasan Permukaan Baja ST. 42 Pada Proses Bubut Konvensiona,” Jurnal Teknik Mesin, vol. 1, no. 3, 2013.

[5] D. Rahdiyanta, “Media Pendingin untuk Proses Permesinan,” and others, Ed. Universitas Negeri Yogyakarta, 2010.

[6] T. A. Prasetya, “Pengaruh Gerak Pemakanan dan Media Pendingin terhadap Kekasaran permukaan Logam Hasil Pembubutan pada Material Baja HQ- 760,” 2010. [Online]. Available: (http://eprints.uns. ac.id)

[7] Arikunto, “Prosedur Penelitian, Suatu Pendekatan Praktek.” Yogyakarta: Rineka Cipta, 2006.


Article View

Abstract views : 37 times | PDF files viewed : 25 times

Dimensions, PlumX, and Google Scholar Metrics

10.21070/r.e.m.v4i1.2629




Copyright (c) 2019 Angga Hari Setyawan; Iswanto Iswanto

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.