Analisa Kinerja Aliran Fluida dalam Rangkaian Seri dan Paralel dengan Penambahan Tube Bundle pada Pompa Sentrifugal

DOI: https://doi.org/10.21070/r.e.m.v3i2.1884

Author (s)


(1)  Muhammad Marzuky Saleh   (Teknik Mesin, Universitas Muhammadiyah Sidoarjo)  
        Indonesia
(2) * Edi Widodo   (Teknik Mesin, Universitas Muhammadiyah Sidoarjo)  
        Indonesia
(*) Corresponding Author

Abstract


Pump is a device used to move fluid from one place to another through the pipe media as a channel. The pump has 2 important components in its performance, namely: Impeller and pump house (casing). When the pump cannot meet the required capacity it can use series and parallel pump circuits to increase it. When moving the fluid to a high surface or high pressure it will have the specifications of the head and discharge. Fluid flow is a liquid that flows in a pipe. In flow there is fluid pressure and also flow type. There are 3 flow types, namely laminer, transition, turbulent. To reduce turbulence in the flow can be used Tube bundle which is a device consisting of several pipes that are tied together that are attached to a cross section in the pipe. This research was conducted in 4 testing stages, namely series circuit with additional tube bundle, series circuit without additional tube bundle, parallel circuit with additional tube bundle, parallel circuit without additional tube bundle. Each test takes fluid pressure, discharge, flow type. From the results of this study it was found that the parallel circuit pump with an additional tube bundle produces fluid pressure, discharge, flow velocity smaller than the series circuit, whereas when without additional the parallel tube pump bundle produces a fluid pressure, discharge, flow velocity greater than the circuit series, while for the flow type of this study is turbulent flow.



Keywords

Pump Series and Parallel Circuit; Discharge; Fluid Flow; Tube Bundle



Full Text: PDF



References


[1] R. Y. Pradhana and E. Widodo, “Analisa Pengaruh Variasi Diameter Pipa Tekan Pvc Pada Pompa Aksial Untuk Kecepatan Gaya Dorong Air,” 2017.

[2] H. Sofwan, “Analisa Kerusakan Pompa Sentrifugal 53-101c wtu Sungai Gerogot PT. Pertamina RU III Plaju,” J. Desiminasi Teknol., vol. 2, no. 1, pp. 29–42, 2014.

[3] Tukiman, P. Santoso, and Ari Satmoko, “Perhitungan Dan Pemilihan Pompa Pada Instalasi Pengolahan Air Bebas Mineral Iradiator Gamma Kapasitas 200 Kci,” no. November, pp. 339–351, 2013.

[4] M. E. Ir. Ali Mahmudi, Buku Bahan Ajar Pompa Dan Kompresor. BANDUNG: Jurusan Teknik Mesin Politeknik Negeri Bandung.

[5] L. Hakim, “Perancangan Dan Pembuatan Alat Uji Karaktristik Pompa Sentrifugal Susunan Seri Dan Paralel,” Islam indinesiaa Jogjakarta, 2004.

[6] A. W. Priyo, Analisis Penurunan Head Losses Pada Belokan Pipa 180o Dengan Variasi Non Tube Bundle, Tube Bundle 0,25 Inchi, Dan Tube Bundle 0,5 Inchi. Jember: Teknik Mesin Universitas Jember, 2013.

[7] A. Faisal, “Analisa Peforma Pompa Sentrifugal Menggunakan Rangkaian Seri Dan Paralel,” universitas muhammadiyah sidoarjo, 2016.

[8] Nasirwan, “Optimasi Pengujian Pompa Seri Dan Paralel,” J. Tek. mesin, vol. 5, no. 1, pp. 15–21, 2008.


Article View

Abstract views : 80 times | PDF files viewed : 153 times

Dimensions, PlumX, and Google Scholar Metrics

10.21070/r.e.m.v3i2.1884




Copyright (c) 2018 R.E.M. (Rekayasa Energi Manufaktur) Jurnal

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.